Home Products Sight Inserts Custom Work Instructions Matches Customers

Please note:
1) It is recommended that you have a qualified gunsmith install any of our parts. O'Hare Tool, Inc. and Distant Thunder Products assume no responsibility for injury or damage caused by installation of our parts. Please make sure you order the correct part(s) for your rifle. Altered or damaged parts cannot be returned. Please have it done right the first time by a qualified gunsmith.

2) Prices do NOT include shipping, refer to shipping chart. United States customers using PayPal will have shipping added at checkout. If your address is outside the US, please call or email for an accurate shipping rate.

Vintage Gun Parts

Ballard Main Spring

Heat-treated and ready for fitting
by a gunsmith.

Width — .282" on mounting end
.262" at the tip.

Overall length — 2.54"
or 2.62"

Price - $35.00 each plus shipping.
(See chart)

Straight Bar Extractor for #5 Remington Rolling

Uncut for caliber and may require some minor fitting. Gunsmith recommended.
Made from 4140 heat treated steel.

Price - $45.00 each plus shipping. (See chart)

Hopkins-Allen 722 trigger springs

Hopkins-Allen trigger springs

Hopkins-Allen trigger springs are available as show in .032" thick and .082" thick.
Call for prices.

Remington Reproduction Sight Inserts
Reproduction Remington sight inserts
[click to enlarge]

We are now making a reproduction set of four inserts for the front sight on the Remington model 341-P and 41-P target rifles. This set closely reproduces the original set that came with the rifles. The set of four is $55.00 plus insured shipping (see chart). 

Other styles of inserts are available for these sights on a custom order basis and are $16.00 each plus shipping (see chart). 

x
Select an insert style and its specifications below. To order more than one insert, select one, add it to the cart, then select another, add it, and so on.
Lollypop Lollypop ( aperture x annulus wall, w/ post)
2-Wire 2-Wire ( aperture x annulus wall, w/ wire)
3-Wire 3-Wire ( aperture x annulus wall, w/ wire)
4-Wire 4-Wire ( aperture x annulus wall, w/ wire)
Crosshair Crosshair ( wire)
Post Post ( post)
4 Post 4 Post ( center, posts)
3 Post 3 Post ( center, posts)
Duplex Duplex ( center, wires,
posts)
Split Bar w/window Split Bar w/Window ( split w/level window)
Split Bar Split Bar ( split)
Rectangle Rectangle (rams & pigs)
4 Minute Dot Minute Dot
2

Main spring for a large frame Remington Rolling Block
with the lower tang bent to a pistol grip

Remington Rolling Block main spring bent to a pistol grip
[click to enlarge]

Heat-treated and ready for fitting by a gunsmith.
Width — .422" on mounting end & .280" at the tip.
Mounting hole — .218" diameter.
Overall length — 3.656"

Price - $40.00 each plus shipping. (See chart)

Ballard .22 RF Extractor set

Price: $75.00 each set, plus shipping
Extractor only: $47.50 + shipping
Actuator only: $37.50 + shipping

Contact me about other hard-to-find replacement parts. New parts are being added to those listed here all the time. If you have a need for a part you can't find anywhere, call and I will see if it is something that we can make.

Ballard Centerfire Extractor

Ballard Centerfire Extractor

May require some minor fitting. Gunsmith recommended. Made from 4140 heat treated steel.

Uncut for caliber………$50.00 plus shipping 

Cut for caliber…$65 + shipping 

(shipping chart)

Breechblock and sear spring for the No. 2 Remington Rolling Block

Breechblock and sear spring for the No. 2 Remington Rolling Block

$45.00 plus shipping 

Rotary extractor for
No. 1 & 1½ Remington Rolling Block

Uncut for caliber. 4140 heat treated steel.

Two models available: No.1 RRB
No.1½ RRB

Price each……$50.00 plus shipping.

Ballard Links, Set of 6

These links are available as individuals or sets of six and are used as replacements to the original link to remove play between the lever and breech block in original actions. Each link has a different hole spacing starting at .312" and up to .337. Made of A2 steel and heat treated. Each link is marked with the hole spacing for easy identification.

Set of 6……………...$125 plus shipping 

Single link (center-to-center hole size:)………$25 plus shipping (see chart) 

Winchester Model 99A inserts

Winchester Model 99A inserts

Thirteen styles of inserts are available for the Winchester Model 99A front sight: simply select your style and specs in the chart to the right. All 99A inserts are cut from .020" high strength steel with a flat black finish and are $18.50 each plus shipping (see chart).

Please note that the sight in the photo is not included.

Inserts for a wide variety of other sights are available on a custom order basis; see the insert page.

Select an insert style and its specifications below. To order more than one insert, select one, add it to the cart, then select another, add it, and so on.
Lollypop Lollypop ( aperture x annulus wall,
w/ post)
2-Wire 2-Wire ( aperture x annulus wall,
w/ wire)
3-Wire 3-Wire ( aperture x annulus wall,
w/ wire)
4-Wire 4-Wire ( aperture x annulus wall,
w/ wire)
Crosshair Crosshair ( wire)
Post Post ( post)
4 Post 4 Post ( center, posts)
3 Post 3 Post ( center, posts)
Duplex Duplex ( center, wires,
posts)
Split Bar w/window Split Bar w/Window ( split w/level window)
Split Bar Split Bar ( split)
Rectangle Rectangle (rams & pigs)
4 Minute Dot Minute Dot
Jim Kluskens, O'Hare Tool, Inc., W8515 County Road N, PO Box 138, Niagara, WI 54151, 715-251-3839, Fax 715-251-3834